Dishwasher Help Forum

Bosch Exxcel Auto Option

Forum to get help and advice on any dishwasher problems that you may have for full size, slimline dishwashers. For dishwasher spares click here

Moderators: r600a, johnmac11, eastlmark, Jackal, Del, Dave_Conway, don, iadom, Penguin45, Dales-Electronic


  • Advertisement

Post a reply

Bosch Exxcel Auto Option

Postby PCAConsulting » Wed May 16, 2012 11:18 am

No SGS56E02GB/47

FD 8403

001784

I have pressed reset buttons in (Eco 50 and Prerinse) and the machine seems to be cycling through diagnostics I am now unable to exit and put the machine back into its normal state, Please help
User avatar
PCAConsulting
Appliance Forum User
Appliance Forum User
 
Posts: 7
Joined: Wed May 16, 2012 11:09 am
Top

Advertisement

Find an dishwasher engineer for repair your dishwasher

Re: Bosch Exxcel Auto Option

Postby Martin » Wed May 16, 2012 11:31 am

Turn power off at the machine and at the wall switch. Turn both back on, press the two reset buttons again for 3 seconds. The number 0 should appear on the display and the machine drain out for 60 seconds, it then will switch off automatically (hopefully). :D
User avatar
Martin
Appliance Guru
Appliance Guru
 
Posts: 18694
Joined: Thu Jun 19, 2003 12:00 am
Location: Hampshire
Top

Re: Bosch Exxcel Auto Option

Postby PCAConsulting » Wed May 16, 2012 11:36 am

THanks, have just tried
Doesnt switch back on unless i press reset buttons before pressing on button
User avatar
PCAConsulting
Appliance Forum User
Appliance Forum User
 
Posts: 7
Joined: Wed May 16, 2012 11:09 am
Top

Re: Bosch Exxcel Auto Option

Postby PCAConsulting » Wed May 16, 2012 11:41 am

Comes on with C9 in the LED, then PO, with pre rinse flashing and Quick 35 lit
User avatar
PCAConsulting
Appliance Forum User
Appliance Forum User
 
Posts: 7
Joined: Wed May 16, 2012 11:09 am
Top

Re: Bosch Exxcel Auto Option

Postby Martin » Wed May 16, 2012 11:48 am

OK, try this:-

With the machine switched off, press and hold the Quick Wash button only (thats the one in the middle of the two reset buttons) Then turn machine on, release Quick wash button then switch off.

Switch back on again and with any luck.........???????
User avatar
Martin
Appliance Guru
Appliance Guru
 
Posts: 18694
Joined: Thu Jun 19, 2003 12:00 am
Location: Hampshire
Top

Re: Bosch Exxcel Auto Option

Postby PCAConsulting » Wed May 16, 2012 12:07 pm

Returns H:04, after following switch on routine, then after switching off, no response at all when switching back on!
User avatar
PCAConsulting
Appliance Forum User
Appliance Forum User
 
Posts: 7
Joined: Wed May 16, 2012 11:09 am
Top

Re: Bosch Exxcel Auto Option

Postby PCAConsulting » Wed May 16, 2012 12:11 pm

H:04 cycles through 0-7, with quick flashing, when pressing quick button
User avatar
PCAConsulting
Appliance Forum User
Appliance Forum User
 
Posts: 7
Joined: Wed May 16, 2012 11:09 am
Top

Bosch Exxcel Auto Option

Postby Martin » Wed May 16, 2012 12:12 pm

:hmm: I'm thinking the circuit board has likely to have gone faulty. :(

Tell, me, what was the sequence of events that prompted you to reset the machine in the first place?
User avatar
Martin
Appliance Guru
Appliance Guru
 
Posts: 18694
Joined: Thu Jun 19, 2003 12:00 am
Location: Hampshire
Top

Re: Bosch Exxcel Auto Option

Postby PCAConsulting » Wed May 16, 2012 12:17 pm

there was no water coming into the machine, although the program would start, looking as though it was washing, but no water in the system
User avatar
PCAConsulting
Appliance Forum User
Appliance Forum User
 
Posts: 7
Joined: Wed May 16, 2012 11:09 am
Top

Bosch Exxcel Auto Option

Postby Martin » Wed May 16, 2012 12:21 pm

Then it will involve some closer mechanical investigation to locate the component that failed. That component (pump, heater, valve etc etc) may also have caused the main control board to fail.....not looking good from where I'm sitting I must admit. :(
User avatar
Martin
Appliance Guru
Appliance Guru
 
Posts: 18694
Joined: Thu Jun 19, 2003 12:00 am
Location: Hampshire
Top

Re: Bosch Exxcel Auto Option

Postby PCAConsulting » Wed May 16, 2012 1:02 pm

Thanks very much Martin, the machine is over 8 years old, so I suspect that the best solution is going to be to replace it. Your help in assisting diagnosis has been greatly appreciated.
User avatar
PCAConsulting
Appliance Forum User
Appliance Forum User
 
Posts: 7
Joined: Wed May 16, 2012 11:09 am
Top
Post a reply

  • Advertisement

Return to Dishwasher Help Forum

 


  • Related topics
    Replies
    Views
    Last post

Who is online

Users browsing this forum: Google Adsense [Bot], Majestic-12 [Bot] and 32 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO
Protected by Anti-Spam ACP
Advertisements by Advertisement Management
Advanced search

Login

Main Menu

User Menu

Who is online

In total there are 34 users online :: 2 registered, 0 hidden and 32 guests (based on users active over the past 30 minutes)
Most users ever online was 510 on Wed May 08, 2013 7:56 pm

Users browsing this forum: Google Adsense [Bot], Majestic-12 [Bot] and 32 guests
Washing Machine Parts Cooker & Oven Spare Parts Tumble Dryer Spares Fridge Freezer Spare Parts Dishwasher Spares Cooker Hood Spares Cleaner Spares Fridge Water Filters