UK Whitegoods Domestic Appliance Help & Support Forums

Washing Machine Help Forum

AEG L75670WD

This forum is for support, help and questions you have about washing machines and washer dryers. For washing machine spares click here

Get spare parts for washing machines

Buy washing machine spare parts in our store for all major washing machine makes and models including many low cost compatible spares or contact us and we will find the parts you need for you

 Support The Repair Community

How you can help in supporting out community is simple, just just use repairers from our online repair search if you need an appliance repaired

Buy any parts you need in our store that helps fund and maintain this website and the free use of it.

Don't use an adblocker.

That's all you need to do and we all appreciate your support and assistance.


by bojomojo » Mon Nov 13, 2017 12:22 pm

The washmaschine fills up with water, spins but it fails to get rid of the water.. so it fill up. Stops and shows an error "10".

Any ideas?
User avatar
bojomojo
Whitegoods Newbie
Whitegoods Newbie
 
Posts: 4
Joined: Mon Nov 13, 2017 12:20 pm

by Martin » Mon Nov 13, 2017 3:31 pm

Error code E10 means a filling time-out. It is taking too long to fill with water. If it fails to drain then that is error code E20 and you need to check the drain filter first.
User avatar
Martin
Appliance Master
Appliance Master
 
Posts: 26297
Joined: Thu Jun 19, 2003 12:00 am
Location: Over the hill

by bojomojo » Mon Nov 13, 2017 5:06 pm

Ok so I did some testing as I thought it was a draining problem.
1. Took out the draining hose and made sure its not blocked.
2. Put it back to the machine and the other end in the sync.
3. Started the rinse program
4. It pushed out water nicely for a min, then started building up water, and after a couple of mins stopped and gave E10.
5. I turned it off and on again, started the rinse program.
6. It pushed out all the water it accumulated last time, and worked fine.

Today morning when the problem originally happened, it kept gathering water till the door sstarted dripping. Because it stopped workimg and showed E10. Then when we opened the door ofcourse the bathroom was flooded

What shall I try next?
User avatar
bojomojo
Whitegoods Newbie
Whitegoods Newbie
 
Posts: 4
Joined: Mon Nov 13, 2017 12:20 pm

by bojomojo » Mon Nov 13, 2017 5:32 pm

Update:
Just did the same test again but with the draini g hose fully contected.
first run it pushes out some water, then keeps fillimg till the water is approx half way up. Then gives E10.
Start second run, it drains some water till its only 1/3 filled then starts. But this time it co tinued to fill up. I stopped it when it was 3/4 full.


- is it supposed to fill more than 3/4 of the trunk?
- how come the door is dripping! Regardless of its a drainimg or filling problem!

I want to at least pin point if the problem is with the mashine or with the water installation to know who to call :D
User avatar
bojomojo
Whitegoods Newbie
Whitegoods Newbie
 
Posts: 4
Joined: Mon Nov 13, 2017 12:20 pm

by Seamy » Mon Nov 13, 2017 8:12 pm

As to who to call, i'd advise an engineer perhaps :lesson:

e10 means the appliance hasn't detected water level reaching required level
User avatar
Seamy
Appliance Veteran
Appliance Veteran
 
Posts: 2901
Joined: Fri Dec 12, 2003 12:00 am

by Martin » Tue Nov 14, 2017 4:27 pm

Yes indeed the water level control has failed often as a result of a blockage in the water level air chamber. Needs checking and cleaning first off.
User avatar
Martin
Appliance Master
Appliance Master
 
Posts: 26297
Joined: Thu Jun 19, 2003 12:00 am
Location: Over the hill

by bojomojo » Tue Nov 14, 2017 7:26 pm

I took the lid off, found that the tube for the pressure switch is not mounted.
Blowed in it a couple of times, then connected it to the switch.
Now its working fine.. lets see if it keeps like that
User avatar
bojomojo
Whitegoods Newbie
Whitegoods Newbie
 
Posts: 4
Joined: Mon Nov 13, 2017 12:20 pm

by Seamy » Tue Nov 14, 2017 9:06 pm

:tup:
User avatar
Seamy
Appliance Veteran
Appliance Veteran
 
Posts: 2901
Joined: Fri Dec 12, 2003 12:00 am



 Washing machine drum paddles

Broken drum paddles or lifters are often a fairly easy part to replace yourself and you can buy replacement drum paddles including many low cost compatible washing machine paddles in our store to fit all major washing machine makes including AEG, Beko, Hotpoint, Bosch and many more

“Drum

Return to Washing Machine Help Forum