Washing Machine Spare Parts

Buy washing machine spare parts in our store at discount prices and get fast support from our team of washing machine part experts with a vast knowledge of the domestic appliance industry

Email us for washing machine parts you need and we'll do the work for you

shop spare parts

User Rating: 2 / 5

Star ActiveStar ActiveStar InactiveStar InactiveStar Inactive

AEG Lavamat Fault Codes

AEG brand logo

These fault codes apply to later AEG Lavamat washing machine version  8*** Series while still produced in Germany, the fault codes for the earlier versions are very similar, almost identical in fact but with some small differences. The earlier set of error codes can be found from this link.

These are the one of the common sets of fault codes for AEG washing machine models that were German made. These fault codes will not apply to models later made in Italy etc.

Before you start any investigation of the fault or even remove the lid of your AEG washing machine please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please remember to support our site by buying AEG washing machine spares from our spare part store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a repairer from the link to the right

  AEG Washing Machine Fault Codes

These fault codes are written for washing machine repairers and not for the general public by AEG and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin.

Please check that any AEG washing machine spares recommended are suitable for use on your particular model and PNC code. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.


Pressure switch fault

  • Imbalance between both washing machine Pressure Switches
  • Water heater or wiring fault



No water intake



Drain pump blockage

  • Drain pump open circuit
  • Water drainage blocked



Safety flood device or switch operated

  • Drain pump fault
  • Electronic module fault



Wash pump faulty

  • Water drain pump faulty



Overheat sensor on main motor activated

  • Main drive motor faulty



Pressure switch fault

  • Water level switch or sensor faulty



Heater or heater relay fault

  • Check heater for continuity
  • Check module



NTC temperature sensor fault detected

  • Check NTC for short or open circuit
  • Check wiring
  • Check module



Motor tacho fault

  • Check main drive motor
  • Check tacho magnet
  • Check tacho coil
  • Check module



MOS-FET transistor for motor triac on main board defective

  • Replace main module



Overfill or level fault



PTC for MOS-FET transistor fault

  • Main motor fault, replace motor



Door interlock fault

  • Check wiring
  • Check washing machine door lock
  • Check door latch etc.



Checksum EEPROM failure

  • Configuration error on module, replace electronic control module

  More AEG Lavamat Washing Machine Help

Should you need more help and guidance please use the links from this article as most of them will help you to understand your AEG Lavamat washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our help and advice forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

Please understand that fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Also do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular AEG washing machine model please post a request to confirm this in the forums.

lavamat fault
aeg Lavamat oko 86720 shows an error code CE and makes an irregular clicking noise but not when spinning
Hi, My lavamat machine made short circuit in whole house during washing cycle. Everything seems OK, but after selection of any program display just jump to the ZERO and beep like when correctly finished. Any idea? Thank you
Hi my AEG lament washer/dryer displays Err on panel and refuses to work. Power is on must not responding! Any help will be much appreciated!
Thank you very much.It does really help a lot!

1000 Characters left