Fault codes for the Amica AWCT range of washing machines that display a fault using a series of lights or LEDs to indicate the fault that has been detected on the washing machine.
The error code is displayed as the relevant lights being lit on the washing machine control panel although the position or function of each LED may differ from model to model.
A sample of the order is shown in the image to the right.
Please remember to support our site by buying Amica washing machine spares from our store and, if you decide that you need an engineer please support the local repairers that help make this site possible, you can search for a repairer using the engineer search facility.
These fault codes are written for washing machine repairers and not for the general public by Amica and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault guide from this link before you begin.
Please check that any Amica washing machine spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine or washer dryer. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.
This is our very simple legend to show the state of the lights, lamps or LED's as they are unlit, flashing or lit continuously.
| Light or LED not lit | Light or LED flashing | Light or LED lit solid, no flash |
|
|
|
|
|
No door lock signal detected / No door lock triac signal / Door not unlocked in two minutesThis fault code can correspond to any of the three faults listed above.
|
|
|
|
|
|
Fill time has exceeded two minutes / No signal from pressure switch after ten minutesThis fault code can correspond to either of the two faults listed above.
|
|
|
|
|
|
Water not drained from washing machine in allotted timeThe level sensor has not detected that the washing machine has been drained inside one and a half minutes or, the machine has not been detected as empty after ten minutes from start of drain.
|
|
|
|
|
|
Overflow - overfilling with waterWater level has exceeded the overfill level on the pressure switch or sensor
|
|
|
|
|
|
Heater or NTC error detected
|
|
|
|
|
|
Washing machine motor does not work
|
|
|
|
|
|
Input voltage incorrectThe power supply voltage is outside of 160-235 Volts, 50/60Hz
|
More Amica Washing Machine Help, Advice And Guidance
Should you need more help and guidance please use the links from this article as most of them will help you to understand your Amica washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.
In addition you can post in our help and advice forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.
You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:
Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Amica washing machine model please post a request to confirm this in the forums.
Can't Find It? Need More Help With Your ?
Getting help, buying spare parts or getting a service engineer for can range from being a simple task to a difficult one as you try to pick your way through model numbers, serial numbers, ranges and all sorts of information. We try to make this as easy as possible for you.
| To get technical help with your then please click here for our help and support forums | |
| Contact us for spare parts using our online contact form, simply click this link to get in touch |
Get more information faults, spare parts and repairs using the custom Google search below which will search our forums, the spare parts store and all articles.
With notes on where to get the best help at the end of each line:
Spares Help - From the store "Contact Us" option or spares@ukwhitegoods.co.uk
Technical Help - Please use the forums
How To Repair Problems - Please use the forums