Buy Washing Machine Spare Parts

Get support and help to find and use this link to buy washing machine spare parts in our store from our team of spare part experts with a vast knowledge of the domestic appliance industry

  Use our support desk to get help on washing machine spare parts

  Or email us for washing machine spare part help and advice or to find a spare part for you

Or call us on  01563 557156

Pay for washing machine spare parts securely online

Pay for washing machine spare parts using Paypal

How To Fit A Washing Machine Door Seal Gasket

User Rating: 5 / 5

Star activeStar activeStar activeStar activeStar active
 

Door seals are often referred to by different people as door boot rubbers, door gaskets just door rubber seal and a host of other terms. They are generally fairly easy to change with a bit of patience and some DIY skills so long as it isn't one that the front weight has to be removed to get into, then it becomes a whole lot more difficult. But that's what we'll show you in the example below.

Washing Machine Door Seal Quality

Next to washing machine drain pumps and motor carbon brushes washing machine and washer dryer door seals are probably one of the single most commonly replaced spare parts and that means two things, you can very often find low cost equivalent replacements and that on the big sellers there are some really dodgy quality seals out there.

We see them all the time, very often on Ebay unsurprisingly, being sold as genuine or worded in some way as being a pukka or suitable replacement seal. We know they're not as they are being sold for less than we would pay for a decent door seal. You can fit them of course, but we won't advise it and we won't sell or use rubbish spare parts. Cheap is fine, sub-standard isn't.

The reason we won't sell them is that, being engineers and always battling time we don't want any grief when we fit the part and, importantly, we don't want called back in a few months time to replace a part again free of charge. The customer is annoyed, we're out of pocket and really nobody is happy.

How some manufacturers (third party almost every time) cut the cost to be the cheapest is that they use a thinner mould. This results in a door seal we often refer to as being "like a rubber band", as in you can almost poke your finger through the thing with little effort. Just imagine though how well that's going to fare when buttons and zips get to it, I can tell you it doesn't end well quite often.

Or, they use an inferior mould as moulds for these things aren't exactly cheap. So the seal is rough, probably doesn't fit correctly and quite often they don't seal against the door properly. Ironically this often happens in conjunction with the above which leads to an absolutely terrible replacement and an absolutely horrid time trying to fit one.

So yes, if you want to save a few pounds then these seals will fit but, you'll have a pig of a job fitting one and it likely won't last so you will probably end up with a wet soapy floor.

This is why we don't sell them as for a few pounds, sometimes pence, more you can have a far, far better part.

All the popular washing machine and washer dryer door seals are available in our online store or, if you are unsure or simply want some guidance on the correct part to buy just send us an email to This email address is being protected from spambots. You need JavaScript enabled to view it.

How To Replace A Washing Machine Door Seal

For this we're just going to go through the general principals step by step. The machine shown is an ISE CI555WH with photos by Rob Dray and Graham Dixon, the author of the Haynes Washing Machine Repair Manual.

Almost all washing machines will have a front clamp band like this that will have to be removed.

On washer dryers with a hot air funnel things can get a lot more complex as that also has to be released. The system employed will vary but the principals are the same in most cases.
removing the washing machine door seal front clamp band
Next the front lip has to be pulled back to allow the seal to be folded inward inside the washing machine drum. pulling off the washer door seal
On the ISE machine and some other machines the front panel is removable to allow full access, in this case the front weight but this as an example allows you to clearly see what's going on. the washing machine door seal as fitted to the tank

Here you can see the inner clamp band or, in this instance, a clamping spring which holds the door seal in place, being prized off. Many of these door seal clamp bands will have a nut and bolt, often with a 7mm head, that have to be slackened off to release the seal.

After that it is a case of pulling the seal off. Some may be more difficult as they will be "glued" into place using a sealant glue called Debor which you can buy in the shop from this link.

Very often at the bottom of the washing machine door seal there will be a drain hose built into the door seal to drain away any residual water and you simply re-seal this using Debor.

the washing machine door seal inner clamp band being pulled off
To fit the new seal it is sometimes advantageous to use some sort of slippery detergent in the lip to allow easy placement. Please not that if you are using Debor or any other sealant do not do this or the seal will not be correctly sealed. lubricating the door seal for fitting
Almost invariably there is a marker, as shown here, which will determine and allow you to easily see the dead centre top or bottom of the door seal. This is vital to get right or the new door seal may twist when fitted or the drainage from the bottom will not work correctly as it relies on this being correct. door seal location marker
Then work the lip of the seal onto the lip of the washing machine outer tub, just work slowly and methodically.

Once the new door seal is on refit the inner clamp and then fold the seal in just as you did earlier to refit the front panel.
refitting the new door seal to the washing machine
Pull the new door seal through and refit to the front panel of the washing machine then refit the outer clamp.

That's it, you're done.
refitting the outer door seal clamp to the washing machine

Are You Up To The Job Of Replacing A Washing Machine Door Seal?

Now, while this makes replacing the seal seem easy and, to a large extent it is on this ISE machine as it was designed to be easy to repair, on many machines where the front panel is not removable it can be an extremely frustrating and difficult job. On many you are liable to become frustrated, wish you had three hands and you will get skint knuckles and cuts replacing a door seal.

The old split Ariston seals are an absolute nightmare to do if you're not familiar with them, Candy and Hoover seals can be a real pain to do as well, especially washer dryers just as a couple of examples. The point is, have a close look before you buy a seal and see what's involved and try to decide if you feel confident enough to do this. If you decide not to please use one of the approved repair engineers, most door seals will cost between £40 and £70 to replace including the labour, so it's not too bad and the engineer will check the rest of the machine while he's there, advising of any possible issues.

Gravatar
ema
I had no trouble changing the door mechanism (less complicated than the seal, but follows the same dismantling procedure), but refitting the spring ring defeated us, it was too tight. So I took one of those plastic single loop handcuff locks. Detach the spring and thread the plastic strip through the wire hooks, slip the whole thing over the rubber seal and push into place, tighten as much as possible and cut off the excess. Bingo! The straps are thin and mine has rounded edges so will not cut the rubber. I closed the door and noted that there is no pressure on the strap cap. I felt very pleased at solving what is definitely the hardest part of the repair!
Gravatar
Louise kavanagh
Cannot get retaining spring back on the larger one for the inside
Gravatar
Jonathon Cowley
I can attest to the fact that washers with a non-removable front panel are a nightmare to replace the seal on. I spent several hours today trying with my Hotpoint WDL520; several cuts to my hands and almost ending my marriage, I gave up trying to fit the inner retaining band myself and have admitted defeat and called a service engineer. One thing I have learned from this; I will never buy another Hotpoint product again. This machine has been deliberately designed to be difficult to repair.
Gravatar
saqar
please i need a Washing Machine Door Sealfor LG ( f 1403 td2 )

1000 Characters left


Washing Machine Spares

Spare parts for washing machines and washer dryers and all other major domestic appliances

Order  washing machine spare parts in our store

Or if you are unsure what part you need for your washing machine just ask us, we're happy to assist you

  Use our online support for spare parts Use our online support desk for spare parts
  Email us for spare parts Email us for help with washing machine spare parts

 

Or call us on
01563 557156

 

more diagnosis & repair help

fault or error codes

All the error and fault codes that we've come across published along with what they mean and what you can do about it to repair your appliance Read More

spare parts information

A wealth of articles that can help you to identify spare parts, diagnose specific spare parts and ordering advice to make sure you get what you need when it comes to parts Read More

support forums

Get help from experienced appliance engineers diagnosing problems with just about any major kitchen appliance you can think on in the UK, almost all have been seen by the engineers that will help you for free if they can Read More

get your appliance repaired

If you don’t fancy trying to repair the machine yourself or, think you need a little professional assistance from an appliance engineer you can find a local engineer here using out free search Read More