Cooker & Oven Spare Parts

Buy cooker, hob and built in oven spare parts in our store with many low cost spare parts and get speedy help from our team of oven and cooker part experts who have a vast knowledge of the appliance industry

Click to email for oven and cooker spare parts you need

shop spare parts

User Rating: 2 / 5

Star ActiveStar ActiveStar InactiveStar InactiveStar Inactive
 

Hotpoint oven and cooker error codes and spare partsThis set of fault codes for a range of Hotpoint built in ovens and may also cover some Hotpoint cooker and range cooker models. We suspect that these codes relate to US Hotpoint models which may not correlate to UK models.

Sadly we do not have a note of the Hotpoint oven model numbers that these error codes relate to.

These error codes may not relate to ALL Hotpoint branded built in ovens.

Before you start any investigation of the fault on your oven or cooker please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please try to support our site by buying Hotpoint spares from our store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can find local repairers using our engineer search facility.

  Hotpoint Oven Spares

We have purposely not listed any Hotpoint spares in this article as there is a vast range of spares used by Hotpoint and, we can't say for sure which models that these codes will relate to.

For spares, if it isn't obvious which one is required please contact us and ask and have the date code and serial number from the rating plate of the oven or cooker. The serial number is like a VIN number on a car, it tells us exactly what part you need and using any other numbers or sizes can be tantamount to a guess. Using the these codes ensure you get the correct part every time.

Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

  Hotpoint Oven Fault Codes

These fault codes are written for oven and cooker repairers and not for the general public by Hotpoint and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a oven or cooker please refer to our basic fault finding guide from this link before you begin.

F0

Stuck touch pad
  • Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced
  • If this fault code cannot be cancelled, replace the oven control, touch pad, or both

 

F1

Stuck touch pad
  • Usually means that either the touch pad or the oven control is defective and needs to be replaced
  • If this fault code cannot be cancelled, replace the oven control, touch pad, or both

 

F2

Overheating detected during baking
  • If actual over temperature condition occurred: Look for welded relay contacts on bake or broil relays. If this happens, replace oven control
  • If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit
  • Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective
  • Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature.

 

F2

Overheating detected during cleaning cycle
  • If actual over temperature condition occurred: Look for welded relay contacts. If this happens, replace oven control
  • If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit
  • Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective.
  • Check door lock switches
  • Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature.

 

F3

Shorted or open circuit oven temperature sensor
  • Check sensor harness and harness connection between oven sensor and oven control 
  • Replace oven temperature sensor if wiring is ok

 

F4

Shorted or open circuit oven temperature sensor
  • Check sensor harness and harness connection between oven sensor and oven control 
  • Replace oven temperature sensor if wiring is ok

 

F7

Stuck touch pad or faulty clock
  • Usually means that either the touch pad or the oven control is defective and needs to be replaced
  • If this fault code cannot be cancelled, replace the oven control, touch pad, or both.

 

F9

Lock switch fault detected
  • Check wiring to door lock switch; the wire harness may be connected wrong 
  • Check for stuck lock switch

More Hotpoint Oven Help

Should you need more help and guidance please use the links from this article as most of them will help you to understand your oven a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.In addition you can post in our forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.You must understand certain things before you begin or attempt any repairs on your own and we want to make these points clear to anyone that decides to investigate one of these or any other oven or cooker:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

You also have to be mindful that fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them. 

Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Hotpoint oven model please post a request to confirm this in the forums.

christopher Heritage
F60 fault code
I have a fault code of F60 flashing on my hotpoint cid641bb induction hob. Anyone know what this is???? Thanks
Ange
Help
Beth said :
My hotpoint oven shows error f03
What does that mean and how can I fix it

Mine is doing the same. My year warranty ran out last week and f03 came up this week. Oven won’t go on at all. So annoyed. Looks like it’s the electronics so I can’t repair it myself and will have to pay for them to send someone !

Beth
Hotpoint oven
My hotpoint oven shows error f03
What does that mean and how can I fix it

Beth
Hotpoint oven error f03
My hotpoint venture shows f03 error code
What can I do

Mr Farrell
Error code F12
My oven keeps displaying F12 and is not complying to any instructions or is permanently turned off, what do I need to do ?!?
Kenneth
Ask in the forums but give the full model number is the best bet.
Nigel Tipper
My new Hotpoint Induction Hob is coming up with the error codes F & L flashing after each other can anyone advise?
Natalie
Error code
Mine is doing the same. What was wrong with yours in the end?
Kenneth Watt
Hi Michelle,If you ask in the forums some of the guys may be able to help but they will need the model number of the oven to help you.
stephen akister
Can you please advise on a fault with my paralitic? oven. Ditital read out says "deno no", when oven is turned on and temperature reads full temp within seconds of being turned on while it is still cold.RegardsMichelle Akister

1000 Characters left