Cooker & Oven Spare Parts

Buy cooker, hob and built in oven spare parts in our store with many low cost spare parts and get speedy help from our team of oven and cooker part experts who have a vast knowledge of the appliance industry

Click to email for oven and cooker spare parts you need

shop spare parts

User Rating: 2 / 5

Star ActiveStar ActiveStar InactiveStar InactiveStar Inactive

Gorenje oven and cooker error codes and spare partsThis set of fault codes for a range of Gorenje built in ovens and may also cover some other oven models as well for other owned brands such as Asko.

Sadly we do not have a note of the Gorenje oven model numbers that these error codes relate to.

These error codes may not relate to ALL Gorenje branded built in ovens but we believe it relates to most of them.

Before you start any investigation of the fault or even remove a panel of the range cooker please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please try to support our site by buying Gorenje spares from our store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can find local repairers using our engineer search facility.

  Gorenje Oven Fault Codes

These fault codes are written for oven and cooker repairers and not for the general public by Gorenje and UK Whitegoods and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on an oven or cooker please refer to our basic fault finding guide from this link before you begin.

  Gorenje Oven Spares

We have purposely not listed any Gorenje spares in this article as there is a vast range of spares used by Gorenje.

Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

Oven Type Key

  • CO: Convection oven, 45 and 60cm
  • PY: Pyrolytic ovens, 45 and 60cm
  • CM: Combi microwave ovens 45cm
  • SM: Solo microwave ovens 45cm
  • CS: Combi steam oven 45cm
  • ST: Steam oven 45cm
  • SA: Steam assist oven 60cm



Oven temperature sensor failure
  • Can be caused by a short circuit or open circuit detected
  • Check connections for the sensor
  • Replace the sensor

Applies to: CO :: PY :: CM :: SA :: CS :: ST



Oven meat probe failure
  • Can be caused by a short circuit or open circuit detected
  • Check the connections on the sensor
  • Replace the sensor

Applies to: CO :: PY :: CM :: SA :: CS



Communications failure between the main board and interface board
  • Check wiring loom and connectors on both boards, if damaged then replace
  • Replace the power board

Applies to: CO :: PY :: CM :: SM :: SA :: CS :: ST



Touch sensor failure on user interface board
  • Replace the user interface board

Applies to: CO :: PY :: CM :: SM :: SA :: CS :: ST



User interface board is overheating
  • Check installation for adequate airflow
  • Check cooling fan system

Applies to: CO :: PY :: CM :: SM :: SA :: CS :: ST



Pyrolytic oven door lock failure
  • Failure to detect the normal operation of the pyro door lock, can be door not closed correctly
  • Check all connections to the door lock
  • Replace the door lock

Applies to: PY



Failure of power board relay supply
  • Replace main power control board

Applies to: CO :: PY :: CM :: SM :: SA :: CS :: ST



Main power board detected as overheating
  • Check the installation for adequate airflow
  • Check cooling fan system

Applies to: CO :: PY :: CM :: SM :: SA :: CS :: ST



Inverter failure: overheating or failure
  • Check the installation for adequate airflow and ventillation
  • Check the operation of the magnetron
  • Replace the inverter

Applies to: CM :: SM



Pyrolytic fails to heat
  • Check the operation of the oven elements
  • Check safety thermostat operation

Applies to: PY



Zero cross failure on the main oven power module
  • When connected to power this error is displayed after thity seconds of a blank display
  • Replace main power control module


Applies to: CO :: PY :: CM :: SM :: SA :: CS :: ST



Steam generator failure

The electronic has detected no change in signal or value from the NTC sensor for the steam generator.

  • Check the connections to the generator and voltages
  • Replace teh generator

Applies to: SA :: CS :: ST



Steam generator NTC failure
  • Check sensor is connected
  • Replace the steam generator

Applies to: SA :: CS :: ST



Door safety switches error detected
  • Check door switches and wiring
  • Replace switch/es if faulty

Applies to: CM :: SM



Maximum time failure on the main oven control board

If the maximum time is exceeded an additional safety feature switches the oven off. To reset this simply turn the oven off and back on again however if the symptoms continue:

  • Replace the main oven control board

Applies to: CO :: PY :: CM :: SM :: SA :: CS :: ST


  More Gorenje Oven & Cooker Help

Should you need more help and guidance please use the links from this article as most of them will help you to understand your oven a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this. In addition you can post in our forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other oven or cooker:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

You also have to understand that fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Gorenje built in oven model please post a request to confirm this in the forums.

M Beaumont
Error 6
I am unable to use my pyrolytic oven due to the door lock being engaged with the door open, resulting in being unable to close door. The message on display is oven cooling. Prior to this I had error message 6
Can you help

M Beaumont
Pyrolytic oven, door lock
I am unable to use the oven due to being unable to close the door due to the lock latch being engaged to lock position with the door open.
Prior to this I had an error messageE6
Please advise

fault code on Gorenje oven
thank you for your article.
Could you please help me with the following fault code on my Gorenje oven ( it 10 years old):
\"02 service\"?
The oven doesnt HEAT niether FAN\'s are working (niether main fan, nor cooling fan). If I turn the oven on, the only things working are: the Display (time) and light of the selctor switch.
I changed selector switch recently.

I suspect on temperature sensor or thermostat fault or fan fault?
Or it may be a faulty control board?

Thank you in advance!

1000 Characters left