Dishwasher Spare Parts

Buy dishwasher spare parts in our store at low prices with quick support from our team of dishwasher spare part experts who will help you find and identify dishwasher spare parts

Email us and ask us to find dishwasher parts for you

shop spare parts

User Rating: 2 / 5

Star ActiveStar ActiveStar InactiveStar InactiveStar Inactive
 

Hotpoint dishwasher error codes and spare partsFault or error codes apply to an the Ultima range of Hotpoint dishwasher models manufactured by under the Hotpoint brand name by the Indesit Company. The fault codes listed here will also apply to models from around 2004 from Creda, Ariston and Indesit as well as Hotpoint as they are all Indesit Company owned brands.

Before you start any investigation of the fault or even remove the lid of the dishwasher please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please try to support our site by buying Hotpoint spares from our store here and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can find a local dishwasher repair engineer using our engineer search facility.

  Hotpoint Ultima Dishwasher Fault Codes

These fault codes are written for dishwasher repairers and not for the general public by Hotpoint and they assume a certain level of competence on the part of the user in diagnostic routines. We may have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a dishwasher please refer to our basic dishwasher fault finding guide from this link before you begin.

Please check that any Hotpoint dishwasher spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your particular dishwasher model. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

AL01

Flood protection system activated
  • Flood protection activated
  • Check pressure switch
  • Check wiring

AL02

Valve or connections - dishwasher will not fill with water
  • Check water supply
  • Check inlet hose
  • Check water inlet valve
  • Check wiring

AL03

Failure to drain
  • Check for blockage
  • Check outlet hose for blockage or obstruction
  • Check drain pump
  • Check wiring

AL04

Thermistor error detected - temperature sensor short, open circuit or out of range
  • Check wiring to thermisrtor
  • Check thermistor

AL05

Circulation pump blocked or faulty
  • Check filters
  • Check circulation pump motor for blockages
  • Check main circulation pump

AL06

Fill timeout
  • Check water supply
  • Check inlet hose
  • Check water inlet valve
  • Check wiring

AL07

Not used
  • This error code is not used on this range of Hotpoint Ultima dishwashers

AL08

Heating timeout
  • Check wash heater
  • Check thermistors

AL09

Software recognition error
  • Reprogram the dishwasher EEPROM
  • Replace electronic control module

AL10

Heating circuit error
  • Check water heating element
  • Check thermostats
  • Check wiring

AL99

Communications error between boards
  • Check wiring between control boards
  • Replace electronic control module

H20

Fill timeout
  • Check water supply
  • Check inlet hose
  • Check water inlet valve
  • Check wiring

  More Hotpoint Dishwasher Help, Advice And Guidance

Should you need more help and guidance please use the links from this article as most of them will help you to understand your dishwasher a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other dishwashers:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

You also have to be aware that Hotpoint dishwasher fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Hotpoint dishwasher model please post a request to confirm this in the forums.

Ray
Alarm A 10 on dishwasher Hotpoint Ultima
Hi can anybody please help. On my Dishwasher Hotpoint Ultima super silent I keep getting the alarm come up AL10 or A10 can anybody please help &tell me what this means & what I can do. Many thanks Ray
tommy ray
my dishwasher ultima shows F3 whats that
J D James
Our Hotpoint Ultima dishwasher has suddenly began to show a flashing "A11" at the right hand side of the display panel.There is no reference to this in the manual.We have switched off and tried another programme and it has then worked...any ideas, please?
Karll001
Ultima FDUD4812
Hi I have the same problem!did you manage to resolve this? Thanks

Steven pipe
My wife purchased A brand new Hotpoint dishwasher model no FDUD4812 18 months ago which sat in packaging until last week, reason being building extension with new larger kitchen which there is room for a dishwasher space, and I plumbed it in ready put it on for the first time and it shows a error code A11= half load valve trial or alternating motor action. Would the fact it has sat there and possibly the valve stuck and if so can it be freed with wd40 or needs replacing can you give any advice please.
gill jeffers
ALo3 displayedI have cleaned the filter and cannot feel any blockagewhat to do next?
Kenneth Watt
Hi Sarah,If you ask in the forums one of the engineers will likely help you but you will need the make and model.
Sarah Dyke
Our dishwasher is displaying the letter F. What does this mean and not working properly ??
JillLordingf
Hotpoint slimline Ultima Dishwasher
My dishwasher is not working properly. After a wash it shows F10 and it seems that it hasnt bin washed in hotwater. Please help.
Kenneth
Please ask in the forums for diagnostic assistance but do provide the full model number or the guys there may not be able to help you.

1000 Characters left