Dishwasher Spare Parts

Buy dishwasher spare parts in our store at low prices with quick support from our team of dishwasher spare part experts who will help you find and identify dishwasher spare parts

Email us and ask us to find dishwasher parts for you

shop spare parts

User Rating: 3 / 5

Star ActiveStar ActiveStar ActiveStar InactiveStar Inactive

Gorenje dishwasher error codes and spare partsFault or error codes used in Gorenje GV and KGV range dishwashers these error codes may also apply to a few other dishwasher brands as well.

We managed to get a test program sequence for this range of Gorenje dishwashers but, it wasn't a very good translation to English and what follows is the best that we could do with what we got.

  How To Carry Out A Dishwasher Test Program

  • Open the door
  • Press and hold program button and switch on the appliance
  • On LED display stands 0A. 
  • The appliance is ready
  • Close the door and test program is activated
  • During the test procedure, you can press program button to next step directly.
  • When test procedure is over, on LED display stands 00

This range also seems to have a pretty poor indication of the fault code along with very vague meanings as to the actual fault being displayed but, we've done the best we could with the information that we have on it. The biggest problem being that we can't determine what LED is flashing!

However, we believe that these dishwashers are made for Gorenjeby either Haieror Midea, so try to cross reference with the fault codes for those for more information.

Before you start any investigation of the fault or open up your Gorenje dishwasher please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please remember to support our site by buying Gorenje spares from our store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a local Gorenje dishwasher repairer using our engineer search facility.

  Gorenje Dishwasher Fault Codes

Like other fault codes these written for dishwasher repairers and not for the general public by Gorenje and UK Whitegoods and they assume a certain level of competence on the part of the user in diagnostic routines. We may have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a dishwasher please refer to our dishwasher fault finding guide from this link before you begin.

Please check that any dishwasher spares recommended are suitable for use on your particular model and production code or serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your dishwasher. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.


Dishwasher fails to fill with water

If the pressure switch or sensor does not detect that the dishwasher has filled with water inside four minutes the buzzer will sound for thirty seconds and the LED will flash, the drain pump will then be run for sixty seconds and the program aborts.

  • Check water supply
  • Check wiring to water valve
  • Check wiring to pressure switch or sensor
  • Check water valve
  • Check pressure sensor or water level sensor


Dishwasher not draining

Dishwasher fails to detect that the water has drained out detected in four minutes, program aborted.

  • Check water drainage
  • Check drain pump wiring
  • Check drain pump


Dishwasher times out when heating

No heat detected in sixty minutes, program aborted.

  • Check wiring to heater and thermostats
  • Check water heating element
  • Check thermostats


Aquastop protection circuit activated

A micro-switch on the Aquastop leak detection system has been switched on for more than two minutes. The dishwasher will shut off the water inlet valve and drain the water aborting the program.

  • Check for water leaks
  • Check float in the base of the dishwasher
  • Check the Aquastop hose if fitted


Not used


Short circuit detected on the temperature sensor
  • Check water heating sensor wiring
  • Check temperature sensor


Temperature sensor detected as open circuit
  • Check water heating sensor wiring
  • Check temperature sensor

  More Gorenje Dishwasher Help, Advice And Guidance

Should you need more help and guidance please use the links from this article as most of them will help you to understand your dishwasher a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you. But if you are in any doubt at all or don't think you are up to diagnosing the fault yourself please the engineer search.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other dishwashers:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

You also have to understand that dishwasher fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Please note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Gorenje dishwasher model please post a request to confirm this in the forums.

Ross Lilley
F12 fault on gorenje dishwasher
I get a F12 fault on my gorenje dishwasher. Sometimes a check of the inlet valve where if joins my water supply clears it but mostly not. Any ideas how I fix it permanently?
Mark Law
Gorenje Dishwasher
My Gorenje dishwasher display cycles quickly through all the codes repeatedly then displays H4 (not E4) I cannot find anything in the manual.

Can you suggest anything?


My Gorenje dishwasher operation time for all modes are same (around 45 min)? How i can fix it?
Dishwasher gorenje Gv60010
Hi my machine is filling up with water and as soon as the wash jets starts to turn it blows the trip in the house so I can\'t see an error code as it clears wen I switch machine back on any help greatly appreciated thanks Neil
Sounds liike it could be a problem with the wash pump but you would really need to use the forums for any more help with that.
E5 code Gorenje dishwasher
My dishwasher starts up but makes a beep-sound after about 5 minutes. When I open it there\'s a code E5. What is wrong?
My dishwasher wont start, H01, cant find anything online about this

You will need the model or ART number from the machine to find that as would we.

Agnes Burns
Program selector not working
My dishwasher is beeping and showing 88. What is wrong? I can't set any program.

1000 Characters left