Washing Machine Spare Parts

Buy washing machine spare parts in our store at discount prices and get fast support from our team of washing machine part experts with a vast knowledge of the domestic appliance industry

Email us for washing machine parts you need and we'll do the work for you

shop spare parts

User Rating: 3 / 5

Star ActiveStar ActiveStar ActiveStar InactiveStar Inactive
 

Beko Fault Codes

Beko washing machine fault codes and spare parts

This set of fault codes only pertains to the Beko WM series of washing machines but it may also relate to other Beko models that use the same PCB from Invensys for a controller and have five LEDs used. 

These error codes may not relate to ALL Beko WM series washing machines. If you are unsure please ask in the forums as well as for all other Beko washing machine fault codes.

Before you start any investigation of the fault or even remove the lid of your Beko washing machine please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please remember to support our site by buying Beko washing machine spares from our spare part store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a repairer from theengineer search facility.

  Beko 5 LED Washing Machine Fault Codes

These fault codes are written for washing machine repairers and not for the general public by Beko and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin which will help you diagnose the problem with your Beko washing machine..

Please check that any Beko washing machine spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

  Fault Code Lights Legend

This is our very simple legend to show the state of the lights, lamps or LED's as they are unlit, flashing or lit continuously.

Light or LED not lit Light or LED flashing Light or LED lit solid, no flash

Beko Washing Machine Fault Codes

The LEDs in these error codes represent the prewash, spin, rinse and then wash LED's as you look at them, being either lit or not lit, they should not be flashing.

H1

Light or LED on constantly when error displayed

Light off when error displayed

Light off when error displayed

Light off when error displayed

Light off when error displayed

NTC (thermistor) Open or Short Circuit

The washing machine has detected an error with the wash thermistor and is reporting this. The error can be caused by either a short circuit or the thermistor itself being open circuit.

  • Check wiring to thermistor
  • Check thermistor normally ~4700 Ohms @ 25˚C ambient

 

H2

Light off when error displayed

Light or LED on constantly when error displayed

Light off when error displayed

Light off when error displayed

Light off when error displayed

Heater detected open circuit

Ordinarily this is the indication of a simple heater failure however it may pay to check the wiring and thermistor.

  • Check wash heater for continuity
  • Check wiring to heater
  • Checck thermistor

 

H3

Light or LED on constantly when error displayed

Light or LED on constantly when error displayed

Light off when error displayed

Light off when error displayed

Light off when error displayed

Heater detected as always on

The wash heater is detected as being on constantly in the washing machine and the machine will abort and shut down.

  • Check wash heater
  • Check wiring
  • Check pressure or level sensor
  • Check heater relay on main control PCB

 

H4

Light off when error displayed

Light off when error displayed

Light or LED on constantly when error displayed

Light off when error displayed

Light off when error displayed

Water inlet valve triac short circuit

The electronic control module has detected a fault in the water inlet valve control triac, namely that it has a short circuit.

 

H5

Light or LED on constantly when error displayed

Light off when error displayed

Light or LED on constantly when error displayed

Light off when error displayed

Light off when error displayed

Drain pump detected open circuit

Ordinarily this will be indicative of a simple drain pump failure.

  • Check drain pump for continuity
  • Check wiring to drain pump

 

H6

Light off when error displayed

Light or LED on constantly when error displayed

Light or LED on constantly when error displayed

Light off when error displayed

Light off when error displayed

Motor triac short

The electronic controller has detected a short circuit on the motor control triac but there are other things to check.

  • Check wiring to motor
  • Check motor
  • Check motor control triac on main electronic board

 

H7

Light or LED on constantly when error displayed

Light or LED on constantly when error displayed

Light or LED on constantly when error displayed

Light off when error displayed

Light off when error displayed

Pressure sensor failure

This error is the electronic controller detecting that there is a failure of the pressure or level sensor however, it can also be caused by an errant reading or signal causing the failure to be detected.

  • Check wiring to pressure sensor
  • Check pressure sensor
  • Check connectors on main control board

 

H11

Light off when error displayed

Light off when error displayed

Light or LED on constantly when error displayed

Light or LED on constantly when error displayed

Light off when error displayed

Motor open circuit

This error can be caused by the motor being oppen circuit or the motor tacho being detected as open circuit. Both can be cause by wiring or connection issues.

  • Check wiring to motor
  • Check wiring to motor tacho
  • Check wiring from electronic controller to the motor
  • Check motor
  • Check motor tacho

  More Help For Beko Washing Machines

Should you need more help and guidance please use the links from this article as most of them will help you to understand your Beko washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our help and advice forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

You also have to know that fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Please note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Beko washing machine model please post a request to confirm this in the forums.

jOANNE
BEKO WMB61431B FABRIC SOFTENER WILL NOT EMPTY- i have cleaned it - is there a fakt finding code
BEKO WMB61431B - fabric conditioner will not empty - I have cleaned it so tere is no blockages . is there a failt finding code please
Dave
WME7247S
Hi. I just clean the detergent compartment because conditioner wasn\'t entering the machine. When put the machine back together the program dial didn\'t work and the flashed up with \" C on \" when I pressed any button.
I took the panel off and found the little board behind the program dial had partially come away. Thought that was it...it was until I pressed a button, any button, and \"C on\" flashed up again. It also has F3 displayed on 3 programmes. Any ideas please?

Daniel Casey
Beko wmc126w fault
Hi, the machine starts to fill then immediately stops..then on the 5 leds the ready led flashes and end stays on steadily. Any ideas?
Glenn
Fault code
Hi. Beko 81445 lw showing fault code 04 17. Will not spin. Any ideas?
Andy
Beko washer
Hi, ive just read your question about fault code 04 17, my washer is just displaying the same and the drum wont move, i cant find hardly any info, did you get sorted?
Regards Andy

Kenneth Bell
Hi did you get it fixed?
Jon
WMS6100W
My 6 months old Beko WMS6100W washing machine is playing up. Initially it would just stay on the wash cycle. I turned it off, undid the filter and let out the water. On turning on again it started ok, filled, but then stayed on the wash cycle again - even though the front lights reflected the position I turned the dial to.
Now I\'ve tried turning it to the \'cottons\' position whilst holding the \'Start/Pause\' button - after a few seconds all the lights start flashing simultaneously for about a minute then go off. Is the PCB module shot?
Thanks.

Kenneth
Hi Jon,

You would really need to ask in the forums on that for any help with it.

Peter
Washing Marchine
beko WM5120s I put the washing in, turn it on, it fills with water, the drum seems to want to spin then cancels, nothing happens after this.
Kenneth
Check the motor carbon brushes first.

After that I would suggest using the forums for more help.

1000 Characters left