Washing Machine Spare Parts

Buy washing machine spare parts in our store at discount prices and get fast support from our team of washing machine part experts with a vast knowledge of the domestic appliance industry

Email us for washing machine parts you need and we'll do the work for you

shop spare parts

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

Hotpoint washing macine fault codes and spare partsThese fault codes are displayed as an error code or fault code on many popular Aqualtis washing machine models from Hotpoint but actually made by Indesit and sold under the Indesit, Ariston and Hotpoint brand names using what is known as the EVO2 software. 

If there are no flashes but door lock led lit and appliance fails to start check door lock, motor heater and associated connections.

  Aqualtis Demostration Mode

To activate hold start/reset and the 4th button (bottom one) for six seconds and “D” will be displayed in the spin speed display.

To deactivate, press and hold start/reset as power is applied for three seconds.

NOTE: Demo mode is not available on all production runs

  Hotpoint Aqualtis Washing Machine Electronic Controller Replacement

These PCB's are often model specific, that is to say that they are dedicated to a particular model or range of model numbers that share the same basic features, do not take it for granted that because they all use the same fault or error code reporting system that they are all the same because they're not. It is also not the case that when it says that there's a communication error or suchlike that the electronic control board is faulty, if you choose to replace it you do so completely at your own risk.

The boards from Hotpoint for an Aqualtis washer will also often need to be programmed. This is done using a program on a laptop (that only Indesit has) or using a pre-loaded card that can be used with a special tool to flash the EEPROM in the washing machine or washer dryer. If you do not have access to either of those and your electronic control PCB needs changed, you will not be able to do it yourself unless you get someone to pre-configure the board for you. Trouble is, you only know if it's correct when you fit the replacement controller.

Most of our approved repairers will be able to carry out these sorts of repairs for you at a reasonable cost.

Before you start any investigation of the fault or even remove the lid of the washing machine or washer dryer please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please remember to support our site by buying Hotpoint washing machine spare parts from our store and, if you decide that you need an engineer please support the local repairers that help make this site possible, you can search for a Hotpoint washing machine repairer using our engineer search.

  Hotpoint Aqualtis Washing Machine Fault Codes

These fault codes are written for washing machine repairers and not for the general public by Hotpoint and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits.

For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin as it will help you to determine the problem with your Hotpoint washing machine. You would also be advised to read our guide on how to repair a washing machine.

Please check that any Hotpoint washing machine spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine or washer dryer. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.


Short circuit motor triac on electronic module
  • Check wiring
  • Check electronic controller



Motor detected as being jammed or motor tacho fallen off
  • Check for objects trapped in the drum
  • Check motor connector block
  • Check wiring
  • Check motor carbon brushes
  • Check tacho connections
  • Check motor



NTC fault - temperature sensor detected as either open circuit or shorted
  • Check wiring to temperature sensor
  • Check thermistor



Pressure switch jammed on empty
  • Check for blockages in pressure switch hose
  • Check wiring to level sensor
  • Check pressure switch is not defective
  • Water inlet valve locked open



Pressure switch jammed on full
  • Check for overfoaming evidence - can trip pressure switch
  • Check for blockages in pressure switch hose
  • Check wiring to level sensor
  • Check pressure switch is not defective
  • Water inlet valve locked open



Not used
  • This fault code is not used on this washing machine



Heater relay stuck
  • Check wiring
  • Check electronic control PCB



Heater relay cannot be activated
  • Check wiring
  • Tap relays as they can jam on new boards
  • Check electronic control PCB



Incompatible EEPROM - Setup Error
  • Reflash EEPROM
  • Check electronic controller



Pressure switch or level sensor not sensing correctly
  • Check wiring and harness 
  • Check level sensor
  • Check electronic control module



Drain pump cannot be activated
  • Check that filter is not blocked or obstructed
  • Check drain hose is clear of any blockage or obstruction
  • Check wiring to drain pump
  • Check drain pump is not defective
  • Check level sensor or switch
  • Check wiring to level sensor



No communications between electronic cards
  • Check wiring
  • Check electronic cards



Communications error on models with three phase induction motor
  • Check wiring
  • Replace power card

  Hotpoint Aqualtis Washing Machine Spares

We have deliberately not given links to any spares in this article and, as you may suspect from this guidance, with very good reason.

Indesit Group appliances are found using two key pieces of information, what the washing machine model number is and the serial number from the rating plate. We can often find them from the model number because we can eliminate multiple instances on occasion and, we know what we're looking at and for, you often won't. But, even with our knowledge even we will often need the serial number or production code to identify the machine correctly and, accordingly, the spares required.

Our advice is very simple, don't guess at it and end up with the wrong parts, contact us from this link and check that you are ordering the correct Hotpoint spares.

  More Hotpoint Aqualtis Washing Machine Help, Advice And Guidance

Should you need more help and guidance please use the links from this article as most of them will help you to understand your Hotpoint washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our help forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:

      • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
      • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
      • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
      • No warranty is inferred, implied or given.

You also have to be aware that fault or error codes are not a "magic bullet" for these Hotpoint washing machines, they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Hotpoint washing machine model please post a request to confirm this in the forums.

cerghit cristinel
ce inseeamna cind apare eroare f19
my ariston aqaltis washing machine F15 error coming and last week I changed PC board is this cause F15 error
Jenny stafford
washing machine beeping all through the cycle every 3/4 minutes
Karen Hague said :
My machine has started to constantly bleep during a cycle no error codes are flashing up and it does complete the cycle any ideas please

Jane Gratton
Hotpoint aqualtis aq113da697s
confused my washing machine the hotpoint aqualtis starts washing for a while then it stops, it doesn't empty the water or rinse and it comes up on the display with the code F 5 and all the lights flash on it so I can't use it because also my dial stopped working it won't move the light to what wash I want it to do, can anyone help me thanks xx
Karen Hague
Bleeping noise
My machine has started to constantly bleep during a cycle no error codes are flashing up and it does complete the cycle any ideas please
Washing machine Ariston Hotpoint Aqualtis Colour Care
This combined washing/drying machine works ok more than 1 year. However, just before one week, even when the machine is turned off there is a continuous sound/beeping signal on every 15-20 seconds. Nevertheless the machine and the programs are ok. What is the reason for this beep and what can I do to stop it? Thank you in advance!
how reset aqualtis?
i change a lot of this...still f5 error... no water arrive. I think it\'s electronic problem. how to reinitialised ?
AQM9D 49X F13error on last 11minutes remain
please let me know the solution of F13 error
model no is AQM9D 49x

aqualtis AQ9D69S F6 fault
Please advise on possible solutions. After completion of washing cycle the door will not open and then the F6 is displayed and flashing repeatedly.
thank you.

Hotpoint aqualtis
Hi did you ever get this sorted as I have the same problem.

1000 Characters left