Washing Machine Spare Parts

Buy washing machine spare parts in our store at discount prices and get fast support from our team of washing machine part experts with a vast knowledge of the domestic appliance industry

Email us for washing machine parts you need and we'll do the work for you

shop spare parts

User Rating: 4 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Inactive
 

Beko WMA Fault Codes

Beko error codes and spare parts

This set of fault codes only pertains to the Beko WMA series of washing machines that have a digital display but it may also relate to other Beko models that use the same PCB control board. 

These error codes may not relate to all Beko WMA series washing machines. If you are unsure please ask in the forums.

Before you start any investigation of the fault or even remove the lid of your Beko washing machine please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please remember to support our site by buying Beko washing machine spares from our spare part store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a washing machine engineer using the engineer search.

  Beko WMA Washing Machine Fault Codes

These fault codes are written for washing machine repairers and not for the general public by UK Whitegoods from information given to us from Beko and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits.

For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin which will help you to diagnose the fault with your Beko washing machine.

Please check that any Beko washing machine spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

E1

NTC error detected

  • Check wiring
  • Check thermistor which will normally read approximately 4700 Ohms at 25˚C

 

E2

Not heating error

  • Check heater as it is detected as being open circuit
  • Check wiring

 

E3

Constant heat

  • Check wiring
  • Check control board relay for heater

 

E4

Filling error detected

You can see the machine constantly filling and discharging water, no wash action or the door is jammed causing this error to occur.

  • Check water valve
  • Check valve triac on PCB
  • Check PCB
  • Check wiring

 

E5

Failure to drain

Often this is reported as being a failure to drain the water from the washing machine, the program taking too long or not spinning.

  • Check for blockages or obstructions in the pump filter
  • Check pump
  • Check pump triac on PCB
  • Check control board

 

E6

Motor fault detected

Often the complaint when this error occurs is that teh washing machine will move a couple of times then the program will end, the machine will jump to spin during a wash or the program is unfinished.

  • Check motor
  • Check wiring
  • Check motor triac on control PCB
  • Check PCB

 

E7

Level sensor error

The complaint will be that the washing machine empties every time it is started of that the program simply does not start.

  • Check wiring to level sensor
  • Check level sensor

 

E8

Failure to fill with water

The washing machine will fail to fill leading to complaints that the program takes too much time, the program does not end, the machine will not fill with water or that the washing machine just drains and nothing else.

  • Check water valve
  • Check anti flood system if fitted
  • Check wiring
  • Check water valve triac
  • Check pump triac
  • Check control PCB

 

E9

Door lock triac failure

  • Check door lock
  • Check wiring
  • Check door lock triac on the main control PCB
  • Check control PCB for operation

 

E10

Door error

The door is detected as being jammed

  • Check door
  • Check door lock
  • Check door lock wiring
  • Check door lock triac on the control module
  • Check control module

 

E11

Motor error detected

  • Check motor
  • Check wiring
  • Check motor triac on control PCB
  • Check PCB

 

E17

Excessive foam detected

Generally this will be as a result of overfoaming from an incorrect detergent being used, a poor quality detergent being used or from overdosing. This is common across many brands especially in soft water areas.

This can take some time to clear and it is advised that you run several rinse only programs to clear any residue detergent still in the washing machine.

  • Reduce detergent dose and restart program

 

E18

Unbalanced load detected

This error can be displayed where the machine has failed to spin or the time can seem to be extended.

  • Sort load and retry spin

  Clearing The Washing Machine Error Code

This process is unconfirmed on certain models but appears to remain valid across the bulk of models.

After entering the failure code observing mode, pressing and holding “Start” button for a approximately five seconds will erase the error code from the memory. After you complete your inspection, if you are not sure that you have solved the problem and if you are going to change the electronic card group, do not erase the error code so that we may investigate any failures.

For all other cases, you may erase the error code.

  More Beko Washing Machine Help

Should you need more help and guidance please use the links from this article as most of them will help you to understand your Beko washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our help and advice forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

Fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Beko washing machine model please post a request to confirm this in the forums.

 

haroun
beko mwd77100
hi i got beko mwd77100 it stopped working the play sign keeps flashing on the screen and when i reset it , it gives e09 any idea guys ???
Kenneth
Please use the forums for that sort of assistance as the repair technicians will not see your comments here.
jayne collins
SE code
any idea what SE code means? please :-(
Kenneth
Hi Jayne,

On what model?

Fault codes will apply to a range of machines and clearly that one is not used on the range that the codes here are for.

sue
Beko frount loader
Load was unbalance and stopped now wont start a progam It come up with E12 ad goes to end with beepng noise
Clegg34
Hi, I have a beko wmb71231, this week the motor failed with one of the windings going short to earth causing the fuse at the plug to blow and taking the socket trip out also, I have replaced the motor and all seemed well, the machine shows no faults and I can select any program and seems to work without fault, my problems is the door is locked and the ready light flashes at the end of a program constantly and the door remains locked, I scrolled through the test sequence ok, I have tried to hold the start / cancel button but it doesn't seem to reset ie. It doesn't complete a drain sequence, any ideas??
Deborah Harper
How to reset beko wme7227s
Phil99
Hey guys can you tell me the restart procedure for the beko xl9 washing machine after having carried out a factory reset cheers
John Austin
E17 fault code how to fix it
Mike beddall
No program held cancel button in turned off mains switched back on program retuned but now it keep filling up with water

1000 Characters left