Fridge & Freezer Spare Parts

Buy fridge, freezer and fridge freezer spare parts in our store and get fast help from our team of refrigeration part experts that have a huge knowledge of the appliance industry and refrigeration spares

Email us for help with fridge and freezer spare parts

shop spare parts

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive
 

Beko American fridge freezer error codes and spare partsThese fault codes relate to many error or fault codes that are displayed on the Cosmos series of Beko side by side American style fridge freezer models that will normally have a model number starting with ASD. However these codes and test procedures may not apply to all Beko American fridge freezers in this range.

Please use the forums to ask if you are unsure.

The error code is displayed as a digital code, exactly as you will see below with little variation on most models.

Since the fault codes for these Beko fridge freezers for the general public's use they may not offer a lot of help in many cases. For the service engineer they give a steer in the right direction but, that's about it really. Beyond the general meanings it is down to investigation and proper fault diagnosis.

Before you start any investigation of the fault or even remove the any part of the fridge freezer please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please remember to support our site by buying Beko spare parts from our store and, if you decide that you really need an fridge repair engineer please support the local repairers that help make this site possible, you can search for a repairer using the engineer search.

Note! There are three disctinctly different versions of the electronic controls used in this range and the service test especially is different for each one

For spare parts this also means that we encourage you to check with us before ordering any as there are differences. Best to locate teh rating plate, normally in the fridge inner wall, left hand side and give us the full model and production code to ensure any spare parts are suitable for your model. Or, just take a picture of it and email that to This email address is being protected from spambots. You need JavaScript enabled to view it.  with your requirements.

  Service Test Version 1

The display board Beko use in this version of the ASD range fridge freezer has a touch-control key system.
When the fridge freezer is energised initially, display board's version revision and then control board's version-revision info is shown on the display.

When the Select button is pressed, selected component will run. It will stop when pressed again. When any component is started, warning icon turns on, when stopped, warning icon turns off.

Beko fridge freezer service test 9

After the refrigerator is energised the fridge set and freezer set buttons are pressed for 2 sec. concurrently within first 30 sec. and freezer set button (select) is pressed 4 times (password 0-0 -0-0 is entered) to switch to service test.

Beko fridge freezer service test 10

To get the fridge freezer into service mode by following the steps are applied respectively as detailed.

Step 1: Buzzer will be sound for a short time. After that, LEDs will illuminate for 0.5 sec and go off for 0.5 sec.

Beko fridge freezer service test 11

Step 2: When any button is pressed, Step 1 is terminated.

Software version is shown on the FF compartment and the revision info is shown on FRZ compartment as follows.

Beko fridge freezer service test 12

Step 3: Freezer Set and Fridge Set buttons are briefly pressed on simultaneously, selected components are started to be driven. By pressing the Select button, selected components are made "On" and Off". At this step, the Fans, Blue led and Illumination LEDS are turned on.

  • Freezer Illumination
  • FF Illumination
  • Blue Light
  • FF Fan
  • Freezer Fan (fan is connected to the compressor in the A+ products and it does not run.)
  • Condenser Fan

Beko fridge freezer service test 13

Beko fridge freezer service test 14

Step 4: When any button is pressed, sensor is started to be shown. Sensor display is as follows.

  • 1st View (Sensor-Value) : Sensor value and sensor code
  • 2nd View (Sensor-Cabin): Sensor value and Cabin abbreviation "CA"
  • 3rd View (Sensor-Cabin Code): Sensor value and cabin code

Beko fridge freezer service test 15

Beko fridge freezer service test 16

Beko fridge freezer service test 28

  Beko American Fridge Freezer Fault Codes

Error codes is displayed at freezer display and while there is a warning icon that will be lit on the display.

These fault codes are written for appliance repairers and not for the general public by Beko and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on refrigeration please refer to our basic refrigeration fault finding guide from this link before you begin.

Further help on how frost free refrigeration works can be found in this article.

E0

Freezer air thermistor or sensor error
  • Displayed if measured sensor value is open circuit or short circuit
  • Resets if the sensor value is correct (not open or short) error is omitted
  • Check wiring
  • Replace sensor
  • Check control module

 

E1

Freezer evaporator or defrost sensor / thermistor error
  • Check wiring
  • Replace sensor
  • Check control module

 

E2

Fridge compartment evaporator or defrost sensor / thermistor error
  • Check wiring
  • Replace sensor
  • Check control module

 

E3

Fridge compartment air sensor or thermistor error
  • Check wiring
  • Replace sensor
  • Replace control module

 

E4

Defrost heater error
  • Check wiring
  • Check defrost heater for continuity
  • Check module

 

E8

Icemaker or ice thermistor sensor error

Displayed if the module measures the sensor value as open circuit or short circuit. The ice maker will not operate.

  • Check wiring
  • Check sensor
  • Check module

 

E9

Ice machine failure

If switch does not change as described during initialisation or, while rotating ice machine, if switch position does not change in 1 minute. The icemaker should not operate.

  • Check wiring
  • Check icemaker unit

 

E13

Freezer fan speed error or failure
  • Check wiring
  • Check freezer fan for blockage or failure

 

E15

Condenser fan speed error or failure
  • Check wiring
  • Check condenser fan for blockage or failure

 

WARN

Warning icon appears in display indicates high temperature alarm

Various reasons can cause this to occur

 

 

-

Cooling failure for electrical resons

This code, if you get it, means you need to run the service test to try to determine the nature of the problem and it is listed below also as being a freezing error as it applies to both the fridge and freezer sections individually.

  • Check wiring
  • Check icemaker unit

 

-

Freezer error due to electrical issues

As above however if the fridge side is still operational as normal then run the service test and check that the fridge heater is operational with a meter, i.e. not open circuit.

  Beko Fridge Freezer Spare Parts

Please check that any Beko spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your fridge freezer. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

  More Beko Fridge Freezer Help And Guidance

Should you need more help and guidance please use the links from this article as most of them will help you to understand your Beko American fridge freezer a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our fridge freezer forum after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other American fridge freezers:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

Please understand that these Beko fridge freezer fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them. 

Note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Beko fridge freezer model please post a request to confirm this in the forums.

1000 Characters left