Tumble Dryer Spare Parts

Buy cheap tumble dryer spare parts in our store at low prices and get fast support from our team of tumble dryer part experts with a vast knowledge of the domestic appliance industry

Email us about tumble dryer parts you need

shop spare parts

User Rating: 4 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Inactive
 

Hoover tumble dryer error codes and spare partsThis set of fault codes for the Hoover VHV series of tumble dryer models including both normally vented and condenser tumble dryers and may relate to any other Candy Hoover produced tumble dryer models.

These error codes do not relate to ALL Hoover tumble dryers. If you are unsure please ask in the forums as well as for all other Hoover tumble dryer fault codes.

Before you start any investigation of the fault or even remove the lid or back panel of your Hoover tumble dryer please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!

Please remember to support our site by buying Hoover tumble dryer spares from our store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a tumble dryer repairer from this link.

  Hoover VHV Tumble Dryer Spares

We have purposely not listed any Hoover tumble dryer spares in this article as it covers multiple models from a vast range with numerous changes made to the spare parts used and subsequent replacement spare parts. They will also often look the same or similar yet be different or, look totally different yet be completely compatible as they've been altered.

Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

We would rather take the time to check for you and get it right.

  Hoover Tumble Dryer Fault Codes

These fault codes are written for washing machine repairers and not for the general public by Hoover and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a tumble dryer please refer to our basic fault finding guide from this link before you begin.

On the lower models in this range there is no digital display so you will get a binary code using the built in LEDs or neon lights that give indications and options. These can vary from model to model but the fault or error code will be displayed as a series of flashes, simply count the number of flashes between the pause and that relates to the error codes below. For exsample, one flash is E1, 3 flashes is E3 and so on.

E3

Water tank full
  • Empty water tank
  • Check wiring
  • Check float switch assembly
  • Check electronic controller

 

E4

Program selector faulty
  • Check selector
  • Check control module

 

E5

Front NTC fault - temperature sensor detected as either open circuit or shorted
  • Check wiring to temperature sensor
  • Check thermistor

 

E6

Main electronic control unit faulty
  • Reprogram main electronic control unit
  • Replace control unit

 

E7

Poor airflow detected
  • Check for blockages
  • Check filters
  • Check condenser unit is clear on condenser tumble dryer models

 

E8

Thermal fuse detected faulty
  • Check thermal fuse
  • Check wiring

 

E9

Thermal cut out detected faulty
  • Check thermal cut out
  • Check wiring

 

E10

Missing load
  • No explanation available

 

E14

Rear NTC detected faulty
  • Check rear NTC or thermistor
  • Check connectors
  • Check wiring

 

E15

Heater relay faulty (ccondenser dryer models) or Open front TOC (vented dryer models)

Condenser tumble dryer models:

  • Check heater relay
  • Check wiring 
  • Check heater

Vented tumble dryer models:

  • Check front thermal overload cutout (TOC)
  • Check wiring to TOC
  • Check connectors to TOC

  More Hoover Tumble Dryer Help, Advice And Guidance

Should you need more help and guidance please use the links from this article as most of them will help you to understand your Hoover tumble dryer a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.

In addition you can post in our forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.

You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other tumble dryers:

  • We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
  • We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
  • We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
  • No warranty is inferred, implied or given.

You also have to know that these Hoover tumble dryer fault or error codes are not a "magic bullet", they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.

Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. 

Fay
Error Loc
Hi

I have a hoover onetouch dryer.

An error Loc has appeared on it.
Would anyone know how to remove it so I can start it.

Regards

Indian Paul
Hoover DYC8913B
I have a Hoover DYC8913B which has been totally reliable until it suddenly starting cutting off a few minutes into it\'s cycle & flashing the error code E15, when I open the door steam pours out.....
its always been well maintained & in a small but well ventilated room, any help would be appreciated....

Kenneth
Sounds like it is overheating but why I could not say.

You would really need to ask in the forums for help with that, the techs won\'t see your comments here.

Martin.D
Kelly summerfield said :
I have a hoover tumble dryer that spins round with no heat it spins for about 5 minuets then stops with all control lights flashing what could this be
I had this problem , replace thermal fuse found it inside at the front, the door and front cover have to come off there are 2 sensors on the outlet duct it is the lower one of the two.

Kelly summerfield
I have a hoover tumble dryer that spins round with no heat it spins for about 5 minuets then stops with all control lights flashing what could this be
hubertus mohr
hello1i changed the capacitor on a hoover vhc 7.. modell because the cylinder was not moving anymore. after reassembling the dryer it says e05 after spinning for about 10 seconds. thanks for your help!
Dick Cliffe
Dick Cliffe. I have a Hoover dryer model VHV 680C that does not heat up when running. Then it will stop with all lights on front illuminated. There is continuity across thermal switch at front and across heater matrix but no live shown. Any ideas please.
Nigel Chambers
I have a Hoover dryer model VHV 680C that does not heat up when running. Then it will stop with all lights on front illuminated. There is continuity across thermal switch at front and across heater matrix but no live shown. Any ideas please.
Nigel Chambers
i have a Hoover, model VHV 680C. There is no heat when it's running, then it stops with all lights on front illuminated. Is this a code to what could be faulty. There is continuity across thermostat switch at front and heater element but no live. Any ideas please

1000 Characters left